www.ericthecarguy.com Hello again, I hope you enjoy this latest offering. I’m sure there will be those that disagree with this practice but thats OK, I feel there are times when it can be done and save a bunch of work resealing a tire. This also shows my preferred method of checking for leaks which I hope you benefit from. Don’t forget I have a second channel now ETCG1, stop by and check it out you might like it. www.youtube.com Due to factors beyond the control of EricTheCarGuy, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. EricTheCarGuy assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. EricTheCarGuy recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of EricTheCarGuy, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not EricTheCarGuy. And as always, Stay Dirty ETCG
![[Google]]( http://www.autobodyshoptoronto.com/wp-content/plugins/easy-adsenser/google-light.gif)
what happened to my sisters 2005 corolla and follow the rim and tire on the car at the time of the nail is left tire just went flat, we used the intake system which used
@ Jorgevrod am of the view that the tires are the most important part of the car. I recommend getting two new tires match and if you have aluminum wheels, make sure to clean before installing the new tires, or if you have a leak.
hey that’s my real man. Do not connect the side. I did and it only lasted four months. Just started to shed this weekend. Eric Well I have a question. My tires are very good, wise over, but the leak has so obviously I have to get another, these questions is: I have to go to a place of old tires and looking for an item in the wear or simply buy the same tires, but I new (tires are just eight months). I need to know about my brother, I do nothing until you get your advice.
hey that’s my real man. Do not connect the side. I did and it only lasted four months. Just started to shed this weekend. Eric Well I have a question. My tires are very good, wise over, but the leak has so obviously I have to get another, these questions is: I have to go to a place of old tires and looking for an item in the wear or simply buy the same tires, but I new (tires are just eight months). I need to know about my brother, I do nothing until you get your advice.
@ Turbobuick33 got them at the dealership where I worked.
Where do you buy your air tools with metal handle?
@ GTCHAMPION1 I’m not really sure how to answer that I know what you say is true and I have seen others do worse and get away, but I feel a responsibility to my audience and I want to assure accurate information.
@ Jambe1234567 is legal in the U.S., but as I said in the video business tires many do not recommend this practice.
patch next time!. . . . lol j / k I have 2 outlets in the side of the rear right wheel of my Honda Accord 2006 =- X, which has maintained for months and I had to replace it, but ohh well. . . lol
is that even legal?. . lol thats not a license over Canada!
nobleheight @ In short, you can not put two different sizes of tires on a wheel bearing on a particular unit because it can cause damage to the variance. Also, do not put a car tire at the place where it is called a truck tire to be.
2500 2001 Dodge Van Full My father needs 3 tires. I looked around to be used. I found a tire with a code starting with a P for passengers. Is it acceptable or safe to replace a tire with a tire LT P? Does that pass the safety inspection of the state of PA? Can you do the alignment on one side and LT225/75/16 P235/60/16 the other side (the same rear axle).
1122ss @ n, all that is needed is part of the pin design.
@ Nobleheight I would say the problem is specific to your situation, since in all the years I worked at Honda I just replaced a brake booster that was damaged in a collision, I’m not saying that no good, I have not seen the same frequency you. Maybe you should see the video I made about the care of a spongy brake pedal that I think the problem is much more common in the Honda brake system after repairs.
(Continued) The sinking of the pedal case began yesterday, ie, pump the brake has been skirting along. This means it’s probably not a lot of brake fluid in retirement. brake fluid that is part of the recovery will be difficult to remove. How I can remove the brake fluid from inside the callback? I want to keep the memory.
The pedal in my 99 Accord intermittently began to sink yesterday. In my experience with Honda (which has already passed me four times, for 4 different Honda), the intermittent nature of it indicates that is probably due to a brake cylinder contournement.Voici question. In the neck, two days after replacing the master cylinder, brake booster is bad. How I can do to keep the memory? Is there a way to clean the brake fluid inside the amplifier.
@ EricTheCarGuy I have more gripping surface, it will be easier for me to remove the screws too tight. Besides, I like everything that cosmetics and, therefore, the nonfunctional weight (dead). The nuts have threaded off OEM stupid nut to keep the lid of the bucket. This reduces the gripping surface. Remove the thread useless and have more clamping surface and the nut is less likely to round in the nuts too tight.
@ Some engineer EricTheCarGuy a tight wheel nuts. I have no compressor. I had the hardest time for a good grip on the wheel nut with a wrench to four lanes. The nuts are round, like the surface of the nut is reduced because a portion of the gripping surface has been distributed to keep the line from the top center chevy stupid stupid. The nut has not replaced this thread stupid to keep the lid.
tailed into the wall?
@ Bobinator50000 You are a sick piece of meat, I love it.
@ Nobleheight Well, I think if it works it works. I do not know why you want to change if, as seems very difficult for me.
@ Nobleheight pass inspection PA state security? Do you check? Hee Hee.
My father has a 2005 Chevy Van 1500. It weighs 7200 pounds so it is quite heavy. “I can replace the wheel nut (Original 7 / 8 inches) with 13/16? The cable is the same. Both are 14 x 1. 50.Mais outside is slightly narrower. (0. 8750 “- 0. 8125″ = 0. 0625) T 62. 5 / 1000 of an inch to make a difference in safety on a van £ 7,200?
So what you say is, after a failure can not be moved the wheel in the front axle, put the car on the stands of stone behind back, start the engine, injection of 5 boxes of spray material aersol tire, run the engine in the drive for 15 minutes while the tire rocking back and forth, then fill with air and when it fails again for the tire shop warranty service?. . Heresy!. . . They never complain. . But I know someone’s day was ruined when it was $ 20 well spent.
@ TheBeachbum90210 course, we remain friends, do not take me seriously. Thanks for the comment.